The honest answer to how much continuous gutters cost depends on footage, metal, and what the bid includes, with removal, rot repairs, downspout routing and the discharge point deciding whether two bids are even describing the same job.
Treat the quote as the product. A low per-foot number that skips tear-off, fascia repair or a legal place to send water is a smaller scope, not a better deal. I would not sign until every bid prices the same rooflines, the same metal, and a path that carries water away from the foundation.
Seamless Gutter Cost by Material and Total Project
A standard continuous gutter installation commonly costs $650 to $1,700, with Angi's project estimate putting the average near $1,150. Across the U.S. market, installed prices commonly range from $3 to $25 per linear foot. That spread makes the material and measured footage more useful than a single national average.
Angi estimates gutter labor at $1.40 to $6 per linear foot. Crews may include that charge in the installed price, so check whether a quote separates labor or bundles it with materials.
Metal on a 150-foot roofline
For a 150-linear-foot roofline, Angi lists aluminum at about $4 to $9 per foot, or roughly $600 to $1,350. Galvanized steel is a heavier option, while copper and zinc sit in premium material tiers. The table uses the listed aluminum and steel ranges; its copper range aligns with the higher benchmarks used elsewhere in the article.
| Material | Per linear foot | 150-foot total | Typical use |
|---|---|---|---|
| Seamless aluminum | $6–$12 | $900–$1,800 | Most common residential choice |
| Galvanized steel | $8–$10 | $1,200–$1,500 | Heavier option for hail-prone areas |
| Copper | $30–$50 | $4,500–$7,500 | Premium finish for architectural projects |
| Zinc | Premium tier; price varies | Premium tier; price varies | Niche architectural finish |
Turn footage into a first number
Measure each eave, add the runs, and multiply by the per-foot price for the material you are considering. The table's aluminum range puts 150 feet at $900 to $1,800. That is a planning figure, not a complete quote: roof height, access, removal, and the number of downspouts can change the final total.
Aluminum suits many residential budgets and resists rust. Steel adds weight and strength where hail is a concern; copper and zinc are architectural choices rather than budget alternatives.
Practical rule: Ask the estimate to state linear footage, material, downspout count, roof height, removal, and access. Compare those lines before judging the total.
What Your Seamless Gutter Quote Pays For
Two bids can print the same linear footage and still land far apart. CostOnce's Utah gutter cost guide shows how wide the spread gets: current Utah estimates sit at $5 to $18 per linear foot, or about $875 to $3,150 on a 175-foot home, and published estimates elsewhere scatter installed aluminum across bands of their own. A per-foot price only means something once you know which lines sit inside it.
Three buckets inside a typical bid
That same guide splits a typical Utah project at about 50% materials, 40% labor, and 10% downspouts and hangers. Use the 50/40/10 split as a benchmark for spotting a bid that buries one of the three. Angi's aluminum gutter cost breakdown puts labor alone at about $1.40 to $6 per linear foot, commonly 20% to 50% of the finished price. That band describes straightforward aluminum work; the share climbs when the house is tall, the corners stack up, or the crew opens rotten wood, which is why whole-job labor figures on complex roofs land above it.
| Component | Typical share or range | What it covers |
|---|---|---|
| Materials | About 50% of project | Coil stock formed on site, end caps, corner miters, sealant |
| Labor | About 40% of project | Forming and sealing on site, hanging, cleanup |
| Downspouts and hangers | About 10% of project | Downspout count and size, elbows, hidden hangers |
| Old gutter removal | About $1–$2 per linear foot | Removal, haul-away and disposal |
| Fascia repair | Allowance set after rot is found | Repair or replacement of fascia board, priced after inspection |
| Drainage extensions and splash blocks | Priced by run length and discharge method | Carrying water away from foundation and walkways |
The crew forms the gutter on site from a coil, then hangs it, so labor is fabrication time plus ladder time rather than a delivery fee. Hidden hangers, outlets, and elbows sit in the hardware slice. A bid that says "gutters included" with no downspout count is incomplete.
Allowances quotes skip
Say the aluminum job prices at $1,800. At roughly half materials, that implies about $900 in metal and fittings, with the rest going to labor and hardware. A quote that prints only a foot price, with no removal line and no fascia allowance, can come in short by the haul-away plus whatever rot the old spikes were hiding. On 150 feet, removal at about $1 to $2 per foot adds $150 to $300 before anyone touches the wood. I read a bid with those lines blank as unfinished, because the answers arrive later as change orders. One comparison in the Utah guide found publisher estimates differing by more than the premium continuous-run gutters usually carry over sectional, so the upgrade itself often costs less than the gap between two sloppy bids.
A lower coil price does not guarantee a lower final invoice when preparation, stories, and outlets are still blank.
A 175-foot house with several rooflines prices differently from a one-story rectangle, and a bid that carries discharge to extensions and splash blocks is a different scope from one that stops at the wall. Normalize footage, downspout count, and where the water goes before you rank the totals.
Factors That Change the Price of Seamless Gutters
Price starts with measured linear footage. Every extra foot is metal, hangers, and time on a ladder. Everything else is a cause that pushes that base up or, less often, lets you hold it down.
What the roof asks the crew to do
Each outside corner, inside corner, and valley is a cut, a fitting, and a sealed joint. A simple rectangle might have four turns. A house with wings and dormers can double the fitting time without adding much eave length. Steep pitch slows the same crew and brings fall protection into the day rate. Two-story access adds about $1 to $3 per foot because the work needs a lift or taller ladders and more careful setup.
Profile is the material decision people skip. A 6-inch K-style gutter uses more metal than a 5-inch run and costs more per foot, and it can serve a larger projected roof. NRCS roof gutter guidance tells designers to pick a gutter and downspout layout whose discharge capacity equals or exceeds calculated roof runoff, and to adjust when the drained area is smaller than a table's maximum. A technical sizing reference in that guidance reports that a 5-inch K-style gutter at a 1% slope can serve roughly 4,000 to 5,300 square feet of projected roof at 4 inches per hour, with the served area shrinking as rainfall intensity rises.
Questions that belong on the quote
Downspout count is not decoration. Each added outlet is an elbow, a drop, and a place for water to leave. Guards add a per-foot cost by style and coverage, and they only earn that cost where debris is real. Local labor follows the metro and the season: a booked spring books differently than an open week in late fall.
| Factor | Effect on price | What to ask for in the quote |
|---|---|---|
| Linear footage | Main driver; every foot is priced | Measured length for each roofline |
| Roof complexity | More corners, valleys and joins add labor | Count of corners, valleys and transitions |
| Stories and height | Two-story work adds about $1–$3 per foot | Story count and access method |
| Roof pitch | Steep pitch slows crews and adds safety costs | Pitch and safety equipment included |
| Gutter profile | 6-inch K-style costs more than 5-inch | Profile and capacity calculation |
| Downspout count and placement | Each added downspout adds material and labor | Number, size and discharge location |
| Gutter guards | Added per foot by guard style and coverage | Guard type, coverage and warranty |
| Local labor rates | Higher in peak metro weeks, softer when crews have open days | Labor rate basis or crew hours |
The estimate should name design rainfall, roof drainage areas, gutter slope, downspout spacing, and the profile. Without those inputs, a 5-inch price and a 6-inch price are not comparable.
Oversizing a small roof wastes money. Undersizing a long, steep slope spends the saving on overflow, ice load, and splashback the first hard storm.
Sample Seamless Gutter Estimates for Real Homes
Pipelineon's gutter installation benchmarks put typical U.S. continuous aluminum at about $6 to $12 per linear foot installed. A 150 to 200 foot system therefore falls near $900 to $2,400 before odd geometry, heavy removal, specialty metal, or accessories. Rebuild any total from measured length, not from floor area.
Three aluminum houses and one copper house
Single-story ranch. A clean job looks like 120 feet of 5-inch aluminum, three downspouts, and no tear-off. At $6 to $12, the gutter run is $720 to $1,440, with downspout allowances sitting on top of that base. One story, no haul-away, few turns: this is the number a straightforward bid should look like.
Two-story home. Take 175 feet of 6-inch aluminum with the old gutters coming off. The base is 175 times $6 to $12, or $1,050 to $2,100. Six-inch stock costs more than five-inch because it uses more metal and can drain a larger roof. Two-story access adds roughly $1 to $3 per foot, or $175 to $525. Removal adds about $1 to $2 per foot, or $175 to $350. Stack the lows and the highs and the band is about $1,400 to $2,975. On the quote itself, each of those should be its own line: footage rate, height surcharge, removal. A bid that folds them into one number cannot be compared against a competitor's, and a Salt Lake City bid should also state downspout length, story count, and whether guards are included.
One-story with a fascia question. One hundred fifty feet of aluminum is $900 to $1,800 before wood. Leave fascia as an open allowance. Rot shows up after the old gutter comes down, so a flat "repair included" line with no cap is a blank check, and a bid with no line at all will come back as a change order.
Copper. Copper runs about $15 to $25 per linear foot. On 150 feet of a 6-inch profile, that is $2,250 to $3,750. Copper is a separate budget, not a nicer version of the aluminum math.
| Scenario | Assumptions | Estimated total |
|---|---|---|
| Single-story ranch | 120 ft, 5-inch aluminum, 3 downspouts, no removal | $720–$1,440 before downspout allowances |
| Two-story home | 175 ft, 6-inch aluminum, old gutters removed | $1,400–$2,975 |
| Standard one-story with fascia concern | 150 ft aluminum, fascia repair allowance | $900–$1,800 plus an open fascia line |
| Premium copper home | 150 ft copper, 6-inch profile | $2,250–$3,750 |
Swap in your own footage. Multiply by the foot rate for the profile, then add height, removal, and any wood you have already seen. If you have not seen the fascia, keep that line open on purpose. Then read each bid the way these estimates were built, line by line, so a $1,400 quote and a $2,900 quote on the same house tell you exactly what the extra money buys.
Utah Climate, Stormwater and Permit Rules That Affect Cost
Salt Lake City's freeze-thaw cycles, snow load, and the occasional intense storm turn a gutter quote into a drainage question. Ice sits in a flat or undersized run, then overflow stains siding and loads the fascia. A cheaper channel that cannot carry the storm just moves the water to a worse place.
That is why the discharge line on a bid matters as much as the footage line.
Where the water is allowed to go
Park City's stormwater utility sits inside a state framework that treats gutters, inlets, pipes, culverts, and detention or retention facilities as parts of one stormwater system. Run a downspout onto a neighbor's lot, a sidewalk, or a public inlet and you can buy erosion, basement moisture, or a correction that costs more than the money you saved on the metal.
Price the whole path from eave to release point.
- Size and outlets: Match gutter profile and downspout count to the roof area and the storm, and write the discharge spot on the bid.
- Extensions and splash blocks: Carry water past the foundation and off walkways before you call the job finished.
- Grading or a buried drain: Use these when a surface extension cannot reach a safe release point.
Modern Yard Landscapes explains stormwater management in plain terms if you want the site-level picture before you argue about foot price. For a landlord or an investor, a low install that returns as ice, a wet basement, or a municipal conflict is the expensive bid.
Permits before you compare totals
Permit requirements vary by municipality, and they can shift with historic-district status or any work touching the public right of way. Before you rank contractors, call the local building or public works office and confirm whether a straight gutter replacement needs a permit and where downspouts are allowed to discharge. Then ask each bidder to put the discharge location and any permit handling in writing on the quote itself. A bid that ignores the right of way is not comparable to one that prices it in.
Financing and Warranties to Require in Writing
Payment structure matters as much as the foot price. You can pay cash, finance through a home improvement loan, or fold gutters into a roof or siding job so one schedule covers mobilization for both. I would not pay the balance because the truck is in the driveway.
Tie money to finished work
Use three beats. A modest deposit reserves the date and the coil. A middle payment can track material on site. The final balance waits until the crew is done and you have looked at slope, outlets, and cleanup in daylight, ideally after a hose test at each downspout.
A verbal "we'll warranty it" is hard to enforce. Ask every bidder for the same written sheet.
- Confirm the deposit share and what it reserves.
- Confirm the trigger for the final payment, in writing, after your inspection.
- Get the manufacturer's finish or material warranty, with start date, length, and exclusions.
- Confirm the installer's workmanship term in years, covering seams, fasteners, and leaks.
- Confirm whether each warranty transfers if you sell, which matters for landlords and flippers.
Manufacturer coverage is about the metal and the finish. Workmanship coverage is about how it was hung. Extended coverage a contractor sells on top is a third document, with its own exclusions. If one bid is silent on transfer and another is not, you are not comparing the same protection.
Ways to Lower Your Seamless Gutter Bill
Cut cost by shrinking duplicated work and by refusing metal you do not need. Do not do it by deleting the lines that keep water off the house.
- Bundle the visit: Pair gutters with roofing or siding so access, protection, and cleanup are paid once. A second mobilization is a quiet line item.
- Book a slower week: Crews with open days price differently than crews stacked through the first warm stretch. Ask for a date, not a vague "soon."
- Hand them one measurement: Sketch each roofline and the foot total before you request bids. Matched footage is the only way the per-foot rates mean the same thing.
- Size before you upsize: Have the contractor run the roof area against a 5-inch profile before you default to 6-inch. Extra metal on a small, simple roof does not buy performance.
- Guards only for a real debris problem: Price the guard against the cleanings it removes. Under heavy trees, that trade can win. On a bare lot, you are buying a product you will still inspect.
If you skip guards, plan on maintenance. Teams that protect foundations with regular gutter cleaning treat cleaning as water management, not a cosmetic extra. The cheapest coil is a poor saving when the gauge is thin or a seam is left unsealed. You pay that choice later in dents, leaks, and a shorter run of service.
Compare Itemized Quotes Before You Sign
Normalize every bid the same way, then look at the total. The lowest advertised foot rate loses once the blank lines get filled in.
- Put every bid on the same measured footage, broken out by roofline.
- Lock metal, gauge, and profile, such as 5-inch aluminum versus 6-inch K-style.
- Require the same downspout count, removal and disposal, and fascia allowance on each sheet.
- Compare totals only after those lines match. A blank allowance is a gap, not a discount.
A short site video is a useful way to see what "on the truck, formed to the eave" really looks like before you read the fine print.
Ask each contractor the same questions: Is labor inside the foot price? How many downspouts are priced, and where do they discharge? Is haul-away included? What happens when fascia rot shows up? Which warranty is in writing, and who backs it? How are payments staged? Who confirms any permit and the discharge spot? Homeowners pricing a wet basement at the same time can compare basement finishing budgets so gutter discharge and below-grade work are not planned in isolation.
Superior Home Improvement writes detailed exterior estimates for Salt Lake City area homes, including roofing and siding scopes where a gutter replacement can share the same access and timeline. Ask for a written estimate for continuous gutters that itemizes footage, metal, downspouts, removal, and discharge, with no hidden fees folded into a single foot price. Visit Superior Home Improvement to request that consultation and see how the gutter work fits the rest of the exterior.
